1、PREMIUM MATERIAL: The wind cup of 3 cups wind speed sensor anemometer is made of ABS material, high strength, small startup wind speed, excellent anti erosion performance. 2、ANTI INTERFERENCE: Wind speed meter sensor has strong lightning interference ability, suitable for a variety of harsh environments, strong wind resistance. 3、LIGHTWEIGHT AND PORTABLE, EXTENSION CABLE: The wind speed sensor anemometer is small and lightweight, easy to carry and assemble. Equipped with an extension cable, the length of the extension cable at the connection is 0.8 meters. 4、TWO WIRE OUTPUT METHODS: The professional wind speed sensor anemometer is compatible with two wire outlet methods, bottom outlet and side outlet. 5、APPLICATIONS: Wind speed sensor can be used for wind speed measurement in greenhouse, environmental guard, weather observatory, ships, wharf, aquaculture, advertising gates, meteorology, ocean, environment, airport, harbor, laboratory, industry, agriculture and transportation environment.
Specification
Item Type: Wind Speed Sensor
Material: ABS
Size: Approx. 158x180x70mm / 6.22×7.09×2.76in
Weight: Approx. 272g/9.6oz
Power Supply Voltage: DC9-30V
Telecommunication Type: for RS485 (Default for Modbus Protocol)
Measuring Range: 0～70m/s (Pulse, 485, 232 Output)
Extension Line Length at Connection: Approx. 0.8m/2.6ft
Accuracy: ± (0.5 + 0.02V) m / s (V Represents the Real Time Wind Speed Value)
Resolution: 0.1m/s
Starting Wind Speed: ≤0.8m/s
Maximum Power Consumption: 0.48W
Load Capacity: DC12V Power Supply, Current Type Output Impedance ≤ 350Ω
DC24V Power Supply, Current Type Output Impedance ≤ 900Ω, Voltage Type Output Impedance ≥ 1KΩ
Operating Environment: Temperature -35℃～60℃, Humidity ≤100 Percent RH Without Condensation
Protection Grade: IP64
Widely Used In: Greenhouse, Eco Friendly, Weather observatory, Ships, Docks, Breeding, Advertising Gates, Meteorology, Marine, Environment, Airports, Ports, Laboratories, Agriculture and Transportation and Other Environments of the Wind Speed Measurement.
About the sensor telecommunication protocol description :
First, if you are using a single sensor connected to the computer to read data directly, it is recommended to use the company's private protocol (see page 3), you can visualize the data in ASCII code (hex send, non hex receive);
Second, if you are a multi sensor interconnection with PLC, configuration or programmable collector, it is recommended to use the standard for ModBus RTU protocol.
Third, If there is no special requirement, the default device address in the sensor parameters is 1, baud rate = 9600, protocol for ModBus RTU.
Standard for ModBus RTU telecommunication protocols 🙂
Serial Format
Data bit 8 bits, stop bit 1 bit, parity bit None, default baud rate 9600bps, serial debugging software set to hex send and receive, two telecommunication intervals of at least 500ms or more, CRC in the manual is the parity bit, 2 bytes. The default device address is 1.
for Modbus CRC checking steps :.
1. Preset the 16 bit register to hexadecimal FFFF, call this register as CRC register;
2. Isolate the first 8 bit data with the lower bit of the CRC register and put the result in the CRC register;
3. check the lowest bit by shifting the contents of the register one bit to the right (towards the lower bit) and filling the highest bit with a 0;
4. If the lowest bit is 0: repeat step 3 (shift again) if the lowest bit is 1: the CRC register is iso orthogonal to the polynomial A001 (1010 0000 0000 0001);
5. Repeat steps 3 and 4 until it is shifted right 8 times so that the entire 8 bit data is all processed;
6. repeating steps 2 through 5 for the next 8 bit data;
7. The final CRC register obtained is the CRC code (the CRC code obtained is low before high).
Wiring Method (Wire Sequence Respectively)
Wire Color: Output Signal (Rs485)
Red: Power Positive
Black: A+
Yellow: B-
Green: Power Negative
Distribution Diameter: Approx. 63mm/2.48in
Installation Hol
Delivery & returns: ships from Australian warehouses, usually within 5–12 business days. A few very remote postcodes can’t be reached by our couriers — if yours is one, we’ll contact you before dispatch. Faulty or damaged items are covered under the Australian Consumer Law.
